Latex on johntaro.art
@latex.johntaro.art
For latex crafts and other stuff i do with latex
For my art follow @johntaro.art
For my art follow @johntaro.art
Got new cutting mats in... lego aloy for scale!
October 7, 2025 at 8:16 PM
Got new cutting mats in... lego aloy for scale!
September 21, 2025 at 6:19 PM
Then i cleaned the inside thoroughly and replaced the backing of the mouth with a fresh one! Now it is fixed!
September 21, 2025 at 11:14 AM
Then i cleaned the inside thoroughly and replaced the backing of the mouth with a fresh one! Now it is fixed!
But i can fix this one by taking the inside of the mouth out and replacing it. It took me nearly an hour and a half. First i clean up the old back of the mouth
September 21, 2025 at 11:14 AM
But i can fix this one by taking the inside of the mouth out and replacing it. It took me nearly an hour and a half. First i clean up the old back of the mouth
Previously i had put nfcs in i had either covered them in latex glue (the yellow stuff with solvents) and sandwiched it in between two layers of latex for the nfc i disolve out of the plastic using acetone.
September 21, 2025 at 11:14 AM
Previously i had put nfcs in i had either covered them in latex glue (the yellow stuff with solvents) and sandwiched it in between two layers of latex for the nfc i disolve out of the plastic using acetone.
So it doesnt always go great. I put an nfc chip into the mouth of this shark for it to have a name however when i went to check the shark this morning i found the nfc had started to corrode. Turns out water and amonia in the liquid latex do not mix well with the chip in the nfc.
September 21, 2025 at 11:14 AM
So it doesnt always go great. I put an nfc chip into the mouth of this shark for it to have a name however when i went to check the shark this morning i found the nfc had started to corrode. Turns out water and amonia in the liquid latex do not mix well with the chip in the nfc.
I cut them down too but i have extra glued parts around the valve.
September 20, 2025 at 2:36 PM
I cut them down too but i have extra glued parts around the valve.
Another gummihaj is born!
September 20, 2025 at 2:29 PM
Another gummihaj is born!
Goopening the insides
September 20, 2025 at 2:28 PM
Goopening the insides
New shork who dis
September 20, 2025 at 12:03 PM
New shork who dis
Shork assembly time!
September 20, 2025 at 11:05 AM
Shork assembly time!
Experimenting drawing with liquid latex!
September 10, 2025 at 8:42 PM
Experimenting drawing with liquid latex!
The hexagons ftw
September 9, 2025 at 7:32 PM
The hexagons ftw
The hexagon pattern came out pretty good! Its a bit subtle though! Now to wash and shine it.
September 9, 2025 at 6:15 PM
The hexagon pattern came out pretty good! Its a bit subtle though! Now to wash and shine it.
Finished the hexagon suit :)
September 8, 2025 at 7:35 PM
Finished the hexagon suit :)
Lasering some hexagons because they are the bestagons!
September 5, 2025 at 3:05 PM
Lasering some hexagons because they are the bestagons!
Crotch zip also protected from... accidents
September 2, 2025 at 9:37 PM
Crotch zip also protected from... accidents
Zipper with protection against getting skin stuck.
September 2, 2025 at 8:33 PM
Zipper with protection against getting skin stuck.
This is how i make latex strips
September 1, 2025 at 9:20 PM
This is how i make latex strips
My hands are freaking sweaty as fuuuck. This was so stressful to do
August 31, 2025 at 5:26 PM
My hands are freaking sweaty as fuuuck. This was so stressful to do
Back zipper glue time!
August 31, 2025 at 4:55 PM
Back zipper glue time!
Crotch zipper done!
August 31, 2025 at 3:35 PM
Crotch zipper done!
I use these chalk markers. They come in two sizes i use the thinnest one .
They basically wash out with water :)
They basically wash out with water :)
August 30, 2025 at 9:33 PM
I use these chalk markers. They come in two sizes i use the thinnest one .
They basically wash out with water :)
They basically wash out with water :)