@lukas-1000.bsky.social
hiking - sailing - running - biking - kayak -
photography - electronics - software - physics
I will block all political posts
photography - electronics - software - physics
I will block all political posts
My wife found this present I gave to her about 10 years ago.
Tiny heart shaped PCB with 14 LED around.
Battery still working, pretty low deepsleep power consumtion.
Atmega 328p, two buttons each on a wakeup pin to run two different LED sequences, programed in C.
#maker #pcb
Tiny heart shaped PCB with 14 LED around.
Battery still working, pretty low deepsleep power consumtion.
Atmega 328p, two buttons each on a wakeup pin to run two different LED sequences, programed in C.
#maker #pcb
September 28, 2025 at 7:43 AM
September 22, 2025 at 5:26 PM
Soon I will go sailing with my family, 7 people will join.
51 Bavaria Cruiser, largest ship I ever chartered.
To explain maneuvers and train knots I built this 55cm long model.
old wooden board + printing
#sailing
51 Bavaria Cruiser, largest ship I ever chartered.
To explain maneuvers and train knots I built this 55cm long model.
old wooden board + printing
#sailing
August 4, 2025 at 3:19 PM
Soon I will go sailing with my family, 7 people will join.
51 Bavaria Cruiser, largest ship I ever chartered.
To explain maneuvers and train knots I built this 55cm long model.
old wooden board + printing
#sailing
51 Bavaria Cruiser, largest ship I ever chartered.
To explain maneuvers and train knots I built this 55cm long model.
old wooden board + printing
#sailing
15min warten um zu Beweisen, dass ich ein Mensch bin.
Roboter sind wohl nicht so geduldig.
Roboter sind wohl nicht so geduldig.
July 30, 2025 at 1:07 PM
15min warten um zu Beweisen, dass ich ein Mensch bin.
Roboter sind wohl nicht so geduldig.
Roboter sind wohl nicht so geduldig.
Finished assembly of first waterproof light. Will build 3 more and improve SW for more effects.
Each device connect via WIFI and send UDP broadcast, Android app recognize them and allow invidual control via UDP messages.
Plan is to mount them below stand up paddle boards or kayaks.
Each device connect via WIFI and send UDP broadcast, Android app recognize them and allow invidual control via UDP messages.
Plan is to mount them below stand up paddle boards or kayaks.
July 18, 2025 at 7:49 AM
Finished assembly of first waterproof light. Will build 3 more and improve SW for more effects.
Each device connect via WIFI and send UDP broadcast, Android app recognize them and allow invidual control via UDP messages.
Plan is to mount them below stand up paddle boards or kayaks.
Each device connect via WIFI and send UDP broadcast, Android app recognize them and allow invidual control via UDP messages.
Plan is to mount them below stand up paddle boards or kayaks.
Soldering the battery pad via THT worked perfectly.
But as always, some layout failures happened.
ESP32-S3 XIAO, take care of this tiny mounting slot, took me an hour to find this shortcut. Added Kapton tape between.
And one FET footprint has wrong pin numbering, need to mount it rotated.
But as always, some layout failures happened.
ESP32-S3 XIAO, take care of this tiny mounting slot, took me an hour to find this shortcut. Added Kapton tape between.
And one FET footprint has wrong pin numbering, need to mount it rotated.
July 18, 2025 at 7:42 AM
Soldering the battery pad via THT worked perfectly.
But as always, some layout failures happened.
ESP32-S3 XIAO, take care of this tiny mounting slot, took me an hour to find this shortcut. Added Kapton tape between.
And one FET footprint has wrong pin numbering, need to mount it rotated.
But as always, some layout failures happened.
ESP32-S3 XIAO, take care of this tiny mounting slot, took me an hour to find this shortcut. Added Kapton tape between.
And one FET footprint has wrong pin numbering, need to mount it rotated.
Received PCB for my underwater LED project. Challenge for tomorrow will be to solder the battery pads of ESP32 from backside using the carefully aligned through hole pads.
Its always exciting to solder the first batch of boards and hope no layout errors happened.
Its always exciting to solder the first batch of boards and hope no layout errors happened.
July 16, 2025 at 7:05 PM
Received PCB for my underwater LED project. Challenge for tomorrow will be to solder the battery pads of ESP32 from backside using the carefully aligned through hole pads.
Its always exciting to solder the first batch of boards and hope no layout errors happened.
Its always exciting to solder the first batch of boards and hope no layout errors happened.
Want to go SUP paddling at night. Build a waterproof WIFI controllable RGB LED light to mount below a SUP or kayak.
Prototype work good.
Now I design a PCB for final setup.
40RGB LED + ESP32-S3 Xiao + 3000mAh battery + magnetic field and acceleration sensor + custom Android App
#Arduino #KiCad
Prototype work good.
Now I design a PCB for final setup.
40RGB LED + ESP32-S3 Xiao + 3000mAh battery + magnetic field and acceleration sensor + custom Android App
#Arduino #KiCad
July 2, 2025 at 9:11 AM
June 28, 2025 at 7:27 AM
June 27, 2025 at 5:00 PM